stda 1 3 0 series 130w desktop (or mounting tab) power supply for i.t. equipment C wide input voltage 90 to 260 vac, 47 to 63hz C single and dual output C optional output connector plug C output voltage available from 3 vdc to 55 vdc C input surge current and overload protection C active power factor correction C option: mounting tab or desktop C long hold up time (50ms) C class i insulation C cooling fan included 2 year warranty approvals: single output product number output voltage output current total regulation maximum output power stda130 - s01 3 - 5 vdc 30.00 - 18.00 a 7% 90w stda130 - s02 5 - 6 vdc 23.00 - 19.16 a 7% 115w stda130 - s03 6 - 8 vdc 21.60 - 16.25 a 7% 130w stda130 - s04 8 - 11 vdc 16.25 - 11.80 a 5% 130w stda130 - s05 * 11 - 13 vdc 11.80 - 10.00 a 5% 130w stda130 - s06 13 - 16 vdc 10.00 - 8.12 a 5% 130w stda130 - s07 16 - 21 vdc 8.12 - 6.19 a 5% 130w stda130 - s08 21 - 27 vdc 6.19 - 4.81 a 5% 130w stda130 - s09 27 - 33 vdc 4.81 - 3.93 a 5% 130w stda130 - s10 33 - 40 vdc 3.93 - 3.25 a 3% 130w stda130 - s11 40 - 50 vdc 3.25 - 2.60 a 3% 130w stda130 - s12 * 50 - 55 vdc 2.60 - 2.36 a 3% 130w multi output product number output #1 output #2 maximum output power vonom iomin iomax regmax vonom iomin iomax regmax stda130 - d00 * +3.3v 4a 20a 7% +12v 0a 2a 5% 90w stda130 - d01 +5v 4a 20a 7% +12v 0a 2a 5% 120w stda130 - d01 - 1 +5v 2a 10a 5% +12v 1a 5a 10% 110w stda130 - d02 +5v 4a 20a 7% +15v 0a 2a 5% 120w stda130 - d03 +5v 4a 20a 7% +24v 0.2a 2a 5% 120w mark " * " means " fcc approval " the model number of s01~s12 had been approved by ccc. the model number of s11 had been approved by kc.
electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 26 0 vac input frequency 47 63 hz power factor correction io=full load, vin= 230 vac 0.95 1.00 output power range vin=90 to 26 0 vac 0 130 w input current (low line) io=full load, vin=11 5 vac 1.7 3.2 a input current (high line) io=full load, vin=2 3 0vac 0.7 1.7 a low line inrush current io=full load, 25c ,cool start, vin=115vac 15 30 a high line inrush current io=full load, 25c, cool start, vin=230vac 30 60 a efficiency io=full load, vin=230vac 8 0 85 % line regulation io=full load 0.5 1 % load regulation vin=230vac 3 10 % over voltage protection 112 132 % over current protection 110 150 % transient response io=full load to half load, vin=100vac 4 ms hold - up time io=full load, vin=110vac 50 ms start up time io=full load, vin=100vac 0.3 1 2 s * ripple & noise (peak to peak) full load, vin=90vac 0.5 1 % safety ground leakage current io=full load, vin=240vac 0.5 0.75 ma temperature coefficient all output - 0.04 0.04 %/c * the ripple & noise is under 3.3vdc at 2% max conditions parameter test conditions min. typ. max. unit operating temperature 0 25 70 c storage temperature - 40 85 c relative humidity 5 95 % operation temperature at 25 c , calculated per mil - hdbk - 217f 0.1m hrs der ate linearly from 100% load at 25 c to 50% load at 70c approvals and compliance parameter test conditions min. unit dielectric withstanding voltage for primary to secondary primary to secondary 4242 vdc dielectric withstanding voltage for primary to ground primary to ground 2121 vdc isolation resistance test voltage = 5 00vdc 50 m emi requirements for cispr - 22 vin=2 2 0vac b class emi requirements for fcc part - 1 5 vin=1 1 0vac b class mechanical and pin out note: 1. dimensions are shown in mm & inch 2. weight: 750~916 g approx (exclude the input cord) 3. optional output connector.
|
